JP Hobby 120mm + 10S EDF Ducted Fan Motor 840KV (CW) (Global Warehouse)

DATA SHEET

Length (mm):	80mm (without motor / Cone)
Weight (gr):	620 gr (with motor)
Direction of Rotation (EDF Rotor)	Classic Counter Clock Wize (CW)
EDF Diameter Class (mm):	120
EDF Outside Diameter (mm):	123 mm
EDF Inner Diameter (mm) :	120 mm
Exit Air Diameter (EDF):	120 mm
Rotor Diameter (mm):	120 mm
Blades:	12
Stators:	8
Turbine shroud	Metal
EDF Rotor	Metal
Power System	JP 4250-?
No. of Magnet Poles:	12
Turns/min/Volt (Kv):	840 Kv
Motor Type:	Out-Runner
Motor Diameter (mm):	50 mm
Shaft diameter (mm):	8
Battery Cells:	10s - 37v
Connection:	PK 5.5mm

MORE INFO

120mm + 10S EDF Ducted Fan Motor 840KV (CW)

100% CNC aluminium JP Hobby EDF unit (shroud and rotor) for 10s.

CAUTION: JP Hobby EDF are fitted with specific 12-pole motors compatible with JP Hobby brushless controllers offered as "Must have Accessories" on this page. Only the use of these controllers validates your warranty and ensures the correct functioning of the EDF. JP Hobby EDF are only guaranteed if used with these ESC.

Description

• Jingpin Hobby uses High grade aluminium alloy material for highest rigid structure and lightest weight.
• The shroud acts as a heat sink, removing heat from the motor. This design creates a more efficiently running motor and will provide peak performance while extending the lifespan of the motor.
• The highly rigid structure design is capable of running up to high RPM to produce extremely high efflux velocity for maximum speed and efficiency.
• Anti Blade flying out design,the Blades be safety kept in the shroud and without damage.It is the best replacement for your plastic or carbon shroud if you want to have a safety EDF fan.
• Each metal blade is precisely made of High Grade Aluminum alloy to generate jet airflow. Every blade has been tested for 8 hours of metal fatigue test as well as in the dynamic balance machine for calibration, making it bring a better and safer user experience for every RC fan.
• You could assemble our EDF system with any other motor without losing dynamic balance effect.

The motor and fan unit comes assembled and balanced from the factory.

Measures

About the above measures : they have been read on the test bench with the intake lip on the unit. The measures have been made using a bench stabilized power source. Results may changed depening upon your equipment and situation.

Description / LiPo	10s (37.0v)	10s (42.0v)	10s (43.5v)
Thrust:	5.4 kg	6.1 kg	7.4 kg
Current:	112 A	96 A	118 A
Power:	3763 W	4838 W	5947 W
Recommended ESC:	150 A / HV	150 A / HV	150A / HV
Min. recommended liPo:	5000mAh 40C	5000mAh 40C	6000mAh 40C

Operating the motor outside of the specifications listed above can either damage the motor, battery or esc. It is important that these components are set up properly. Failure to do so can void the warranty. It is strongly encouraged to use a Watt Meter to test the watt and amp performance when setting up a new system. If the output is above the factory recommended specs, then it needs to be adjusted by the esc. The timing and throttle settings on the esc can help to set the appropriate levels.The controller should be chosen 20% over rated due to the long lasting load.
LV = low voltage controler up to 6s, HV = high voltage controler above 6s.
Battery should be chosen about 15/ - 1/20 of the max current for 4-3 minutes WOT. 30-40 C is appropriate.

Specifications

• Special high grade aluminum quality
• Motor Kv: 840
• Motor: MT-4250-12S (8mm axle) Outrunner 12 poles
• Motor diameter: 50mm
• Motor length: 60mm
• Rotor: 120mm 12 blades aluminium
• External diameter: 123mm
• Internal diameter: 120mm
• Inlet ring diameter: 136mm (removable)
• Ejection diameter: 120 mm
• Combo max thrust: 7.4Kg
• Weight: 620g (combo EDF + lip + motor )
• Max efficiency: 90 %
• Recommended max. rotation speed: 75600 tours/min
• Speed Control Advanced Timing Setting: 15° and under
• Connections: Banana / PK 5.5mm (in place)

Content

• 1x JP Hobby 10s 120mm full metal EDF unit (CCW)
• Connectors